Sizes and Specifications | Product Name | Diameter | Tape Material | Core Wire | Loops Per Roll | Clips Per Loop | Weight Per Roll | Length Per Roll/ Attachment Spacing | | | (inches) | (mm) | | | | | (lbs) | (kg) | (ft) | (m) | | Commercial Barrier | 18 18 24 | 450 450 600 | GALV 430 SS 430 SS | GALV GALV GALV | 33 33 33 | 0 0 0 | 12.4 12.4 16.5 | 5.6 5.6 7.5 | 50 ft. @ 18” 50 ft. @ 18” 50 ft. @ 18” | 15m @ 450 mm 15 m @ 450 mm 15 m @ 450 mm | | Barrier | 24 30 36 | 600 750 900 | 430 SS 430 SS 430 SS | GALV Or SS | 31 31 31 | 3 3 3 | 15.6 19.5 23.4 | 7.1 8.8 10.6 | 20 ft. @ 16” 20 ft. @ 16” 20 ft. @ 16” | 6.1 m @ 400 mm 6.1 m @ 400 mm 6.1 m @ 400 mm | | Super Barrier | 30 36 40 60 | 750 900 1,000 1,500 | 430 SS 430 SS 430 SS 430 SS | 304 SS 304 SS 304 SS 304 SS | 51 51 81 81 | 5 5 5 or 7 9 | 32.0 38.4 68.0 102.0 | 14.5 17.4 30.9 46.3 | 25 ft. @ 12” 25 ft. @ 12” 40 ft. @ 12” 40 ft. @ 12” | 7.6 m @ 300 mm 7.6 m @ 300 mm 12 m @ 300 mm 12 m @ 300 mm | | Double Barrier | 24/30 | 600/ 750 | 430 SS | GALV Or SS | 31/31 | 3/3 | 35.1 | 15.9 | 20 ft. @ 16” | 6.1 m @ 400 mm |
For any products not specifically listed here, please call 1-800-510-0840 toll-free for further information. Razor Wire/Barbed Tape Specification Standard Specification. The diameter of the barbed tape obstacle in packaged condition shall be [18”, 24”, 24”/30” (double coil), 30”, 36”, 40”, or 60”] +/- 2”. The tape shall be fabricated from 0.025” [AISI 430 series stainless steel with a minimum Rockwell hardness of (30N) 39, or galvanized high tensile steel]. Each loop shall contain barb clusters spaced 4” on center, and each barb cluster shall have 4 needle-sharp barbs with an average barb length of 1.2” as measured from the center of the cluster. Barbs shall be alternately offset from the tape centerline from 0.15” to 0.45”. The tape shall be permanently cold clenched a minimum of 2300 around a 0.098” diameter [AISI 304 spring quality austenitic stainless steel core wire, or Class 3 high-tensile galvanized core wire] having a minimum tensile strength of [180,000 or 220,000] psi. The finished reinforced barbed tape shall have two continuous cut-resistant strengthening flanges which shall be continuous and straight to each barb root to permit maximum barb penetration. Each roll will consist of [0, 31, 33, 51, 81, or 101] loops with adjacent loops clipped at [0, 3, 5, 7, or 9] equally spaced locations around the circumference to provide the concertina effect. These clips shall be fabricated from 0.065” x 0.375” stainless steel and shall be capable of withstanding a minimum pull load of 200 lbs. Each roll of barbed tape shall cover [10, 15, 20, 25, or 50] linear feet when properly installed. 18" Diameter Commercial Barrier 
|
